Current Building Codes

Effective January 1, 2007

(And locally adopted appendices and amendments)

2006 International Residential Code

  • Appendix A: Sizing and Capacities of Gas Piping
  • Appendix B: Sizing of Venting Systems Serving Appliances Equipped with Draft Hoods, Category I Appliances, and Appliances Listed for Use With Type B Vents
  • Appendix C: Exit Terminals of Mechanical Draft and Direct-Vent Venting Systems
  • Appendix D: Recommended Procedure for Safety Inspection of an Existing Appliance Installation
  • Appendix E: Manufactured Housing Used as Dwellings
  • Appendix G: Swimming Pools, Spas and Hot Tubs
  • Appendix H: Patio Covers
  • Appendix J: Existing Buildings and Structures
  • Appendix K: Sound Transmission

Section 104 "Application" is amended (by State Act 93) to exempt the following from building permit: ‹500 sq. ft carport; ‹500 sq. ft detached private garage; ‹500 sq. ft shed; Agricultural Buildings (see exemption form); Recreational Cabins (see exemption form)

Section 311.5.3 "Stair Treads and Risers" is amended (by State Act 93) to: maximum riser height shall be 8-1/4" and minimum tread depth shall be 9".

Section 403.62 "Permit Requirements & Exemptions" is amended (by State Act 93) to exempt the following from building permit: Uncovered deck, less than 30" above grade.

2006 International Building Code

  • Appendix C: Group U-Agricultural Buildings
  • Appendix D: Fire Districts
  • Appendix E: Supplementary Accessibility Requirements
  • Appendix F: Rodent Proofing
  • Appendix G: Flood-Resistant Construction
  • Appendix H: Signs
  • Appendix I: Patio Covers
  • Appendix J: Grading

Section 903.2.14 "Use Group B": amended to add: An automatic fire suppression system shall be provided throughout all buildings of Use Group B when more than 3 stories of 35 feet in height, or more than 10,000 sq. ft. per floor, in accordance with Section 903.1.1.

Section 1608.2 "Ground Snow Loads": is amended to add: Ground snow loads to be used in determining the design snow loads for roofs are PG 40 per sq. ft.

2006 International Mechanical Code

  • Appendix A: Combustion Air Openings and Chimney Connector Pass Throughs

2006 International Plumbing Code

  • Appendix B: Rainfall for Various Cities
  • Appendix D: Degree Day and Design Temperatures
  • Appendix E: Sizing of Water Piping System
  • Appendix F: Structural Safety

2006 International Fuel Gas Code

  • Appendix A: Sizing and Capacities of Gas Piping
  • Appendix B: Sizing and Venting Systems Serving Appliances Equipped with Draft Hoods, Category I Appliances, and Appliances Listed for Use with Type B Vents
  • Appendix C: Exit Terminals of Mechanical Draft and Direct-Vent Venting Systems
  • Appendix D: Recommended Procedure for Safety Inspection of an Existing Appliance Installation

2006 International Existing Building Code

  • Appendix A: Guidelines for the Seismic Retrofit of Existing Buildings
  • Appendix B: Supplementary Accessibility Requirements for Existing Buildings and Facilities

2006 International Energy Conservation Code

  • Appendix A: Wall Assemblies

2002 National Electrical Code

2006 International Fire Code

  • Appendix A: Sizing and Capacities of Gas Piping
  • Appendix B: Sizing and Venting Systems Serving Appliances Equipped with Draft Hoods, Category I Appliances, and Appliances Listed for Use with Type B Vents
  • Appendix C: Exit Terminals of Mechanical Draft and Direct-Vent Venting Systems
  • Appendix D: Recommended Procedure for Safety Inspection of an Existing Appliance Installation

2006 International Property Maintenance Code

(Request a copy of amendments/alterations/deletions)

2006 International Urban Wildland Interface Code

  • Appendix C: Fire Hazard Severity Form
  • Appendix D: Fire Danger Rating System

2006 International Code Council Performance Code

  • Appendix A: Risk Factors of Use and Occupancy Classifications
  • Appendix B: Worksheet for Assigning Specific Structures to Risk Factors of Use and Occupancy Classifications
  • Appendix C: Individually Substantiated Design Method
  • Appendix D: Qualification Characteristics for Design and Review of Performance-Based Designs
ICC/ANSI A117.1